rf pa5562 wi - fi integrated pa module 4900mhz to 5925mhz revision ds20160218 1 of 5 disclaimer: subject to change without notice www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo product description the rf pa 556 2 is a three - stage power amplifier (pa) designed for wi - fi 802.11a/n/ac systems. the compact form factor and integrated matching minimizes layout area in the application and greatly reduces the number of external components. performance is focused on optimizing the pa for a 5 v supply voltage that conserv es power consumption while maintaining th e highest linear output power and leading edge throughput. a key feature is the integration of a logarithmic power detector which enables power control across the entire power spectrum for applications which use higher gain antennas or end users wanting to reduce device calibration time in production. the rf pa5552 integrates a 5ghz power amplifier (pa), regulator and power detector into a single device . the device is provided in 4 mm x 4 mm x 0. 9 mm, 20 - pin qfn package. functional block diagram packag e: qfn , 20 - pin, 4 mm x 4 mm x 0. 9 mm max feature overview ? p out = +2 3 dbm, 802.11ac, vht80 mcs9 at - 35db dynamic evm ? p out = +25 dbm, 802.11n, ht20/40 mcs7 at - 30db dynamic evm ? p out = +27 dbm, ht20 mcs0 at spectral mask compliance ? optimized for 5 v operation ? typical gain 33 db ? low power consumption ? integrated logarithm power detector ? input and output matched to 50? applications ? wireless routers ? access points ? residential gateways ? consumer premise equipment ? internet of things ordering information part number description rf pa556 2 sb sample bag with 5 pieces rf pa556 2 sq sample bag with 25 pieces rf pa556 2 sr 7" reel with 100 pieces rf pa556 2 tr 13 13 " reel with 2,5 00 pieces rf pa556 2 pck - 410 assembled evaluation board + 5 pieces g n d r f i n g n d p a _ e n n c n c g n d r f o u t v c c 1 v c c 2 v c c 3 g n d g n d g n d 6 n c p d e t n c n c 7 8 9 1 0 2 0 1 9 1 8 1 7 1 6 g n d g n d r e g u l a t o r l o g d e t e c t o r
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 2 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo absolute maximum rat ings note: for r1 placement, refer to evaluation board schematic exceeding any one or a combination of the absolute maximum rating conditions may cause permanent damage o the device. extended application of absolute maximum rating conditions to the device may reduce device reliability. specified typical performance or functional operation of the device under absolute maximum rating conditions is not implied. this is an ingap device designed for high duty cycle applications with tj>30 oc over ambient n ominal operating parameters parameter rating unit dc supply voltage (no rf applied) - 0.5 to +6 v dc dc supply current 10 00 m a operating case temperature - 40 to +85 oc storage temperature - 40 to +1 5 0 oc maximum t x in put power into 50? load for 11a/n/ ac (no damage) . *r1=0? +10 dbm maximum t x in put power into 50?, 10:1 load for 11a/n/ ac (no damage) *r1=15? +1 5 dbm parameter min typ max unit condition compliance 80 2.11a, 802.11n, 802. 11ac operating frequency 5.180 5.925 ghz extended operating frequency 4.9 5.925 ghz power supply v cc 4.75 5 5.25 v pa enable voltage - high 1.7 3 3.3 v pa_en pa enable voltage - low 0 0. 5 v pa_en transmit performance v cc =3.3 v, t=+25oc , v paen =3 v , pa_en=high ; unless otherwise noted 11ac vht160 output power 2 2 db m mcs9 dynamic evm 1 . 4 1.8 % - 3 7 - 35 db 11ac vht 80 output power 2 2 2 3 db m mcs9 dynamic evm 1 . 4 1.8 % - 3 7 - 35 db 11n ht20/40 output power 23 .5 2 5 db m mcs7 dynamic evm 2.5 3 .2 % - 32 - 30 db margin to 802.11ac 160 mhz spectral mask 5 0 db c p out = +23 dbm, mcs0
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 3 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo margin to 802.11ac 80mhz spectral mask 5 0 db c p out = +25 dbm, mcs0 margin to 802.11n 20mhz spectral mask 5 0 db c p out = +27 dbm, mcs0 gain 3 1 3 3 db gain variation - 2.5 +2.5 db t = - 40 to + 85 o c out of band gain - 1 5 - 5 db f = 3300 - 38 00mhz 1 2 db f > 70 00mhz quiescent current 150 165 ma rf=off operating current 29 5 335 ma p out = + 23 dbm 415 475 ma p out = + 27 dbm pa enable control current 1 5 a rfin port return loss 12 db rfout port return l oss 9 db 2 nd harmonics - 4 0 - 35 db m/mhz p out = + 27 dbm 802.11a 6mbps 3 rd harmonics - 4 0 - 35 db m/mhz p out = + 27 dbm 802.11a 6mbps power detector voltage 0.2 5 mv rf off 0.28 mv p out = 0dbm 0.88 mv p out = + 27 dbm power detector slope 2 2 mv/db general specifications leakage current 0.2 10 a rf off; v paen =0v stability output vswr 6:1 cw signal. no spurious above - 41.25dbm/mhz for non - harmonic related signals. output power range 0 2 7 dbm output p 1db 3 3 dbm ramp on/off time 2 00 ns 10%< - >90%; referencing from control voltage to rf power thermal resistance 27 o c /w
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 4 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo evaluation board schematic transmit timing diagram u1 RFPA5562 u1 RFPA5562
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 5 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo pin out pin names and descriptions pin name description 1 nc not connected internally. it may be left floating or connected to ground. 2 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 3 rfin rf inp ut, internally matched to 50? and dc shorted . external dc blocking capacitor required. 4 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 5 paen input enable bias voltage (regulated internally) . 6 nc not connected internally. it may be left floating or connected to ground. 7 nc not connected internally. it may be left floating or connected to ground. 8 nc not connected internally. it may be left floating or connected to ground. 9 nc not connected internally. it may be left floating or connected to ground. 10 pdet power detector . p rovides an output voltage proportional to the rf output power level. 11 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 12 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 13 rfout rf out p ut, internally matched to 50? and dc shorted . external dc blocking capacitor required. 14 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 15 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 16 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 17 gnd ground connection. n ot connected internally and can be left floating or connected to ground. 18 vcc3 third stage supply voltage 19 vcc2 second stage supply voltage. 20 vcc1 first stage supply voltage. pkg base gnd ground connection. the back side of the package should be connected to the ground plan though as short of a connection as possible. pcb vias under the device are recommended. g n d r f i n g n d p a _ e n n c n c g n d r f o u t v c c 1 v c c 2 v c c 3 g n d g n d g n d 6 n c p d e t n c n c 7 8 9 1 0 2 0 1 9 1 8 1 7 1 6 g n d g n d
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 6 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo package outline (dimensions in millimeters) pcb mounting pattern (dimensions in millimeters)
rf pa5562 wi - fi front end module 4900mhz to 5925mhz revision ds20160218 7 of 7 disclaimer: subject to change without notice ? 2016 rf micro devices, inc. www.rfmd.com / www.qorvo.com rfmd + triquint = qorvo product compliance information caution! esd - sensitive device esd sensitivity ratings esd rating: class 1 c voltage : passes 15 0 0 v test: human body model (hbm) standard: jedec standard jesd22 - a114 esd rating: class c2 voltage : passes 5 00 v test: charged device model (cdm) standard: jedec standard jesd22 - c101 msl rating msl rating: level 2 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 solderability compatible with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) soldering processes. rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp - a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free contact information for the latest specifications, additional product information, worldwide sales and distribution locations, and information about qorvo: web: www.qorvo.com t e l : +1 - 844 - 890 - 8163 email : customer.support@qorvo.com for information about qorvo: web: www.qorvo.com
|
